arm: Make interrupts.o and reset.o in libarm also appear in SPL

SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.

Signed-off-by: Tom Wai-Hon

arm: Make interrupts.o and reset.o in libarm also appear in SPL

SPL u-boot may call do_reset() which depends on interrupts.o and reset.o.
So make them also appear in SPL.

Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

arm: move C runtime setup code in crt0.S

Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to

arm: move C runtime setup code in crt0.S

Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().

Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).

Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

show more ...

Merge remote-tracking branch 'u-boot/master'

SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux

In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as

SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linux

In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.

Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

arm: enable libgcc build for SPL

Enable the building of private libgcc for SPL

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry R

arm: enable libgcc build for SPL

Enable the building of private libgcc for SPL

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm:

Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm: Remove unneeded setting of LDCSRIPT
Define CPUDIR for the .lds link script
arm: Remove zipitz2 link script
Allow arch directory to contain .lds without requiring Makefile
OMAP: Remove omap1610inn-based boards
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
board/ti/beagle/beagle.c: Fix build warnings
sdrc.c: Fix typo in do_sdrc_init() for SPL
tegra: i2c: Add I2C driver
tegra: fdt: i2c: Add extra I2C bindings for U-Boot
tegra: i2c: Select I2C ordering for Seaboard
tegra: i2c: Enable I2C on Seaboard
tegra: i2c: Select number of controllers for Tegra2 boards
tegra: i2c: Initialise I2C on Nvidia boards
tegra: Enhance clock support to handle 16-bit clock divisors
fdt: Add function to allow aliases to refer to multiple nodes
tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
tegra: fdt: Enable FDT support for Ventana
tegra: fdt: Enable FDT support for Seaboard
tegra: usb: Enable USB on Seaboard
tegra: usb: Add common USB defines for tegra2 boards
tegra: usb: Add USB support to nvidia boards
arm: Check for valid FDT after console is up
fdt: Avoid early panic() when there is no FDT present
tegra: usb: Add support for Tegra USB peripheral
tegra: fdt: Add function to return peripheral/clock ID
usb: Add support for txfifo threshold
tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
tegra: usb: fdt: Add additional device tree definitions for USB ports
tegra: fdt: Add clock bindings for Tegra2 Seaboard
tegra: fdt: Add clock bindings
tegra: fdt: Add additional USB binding
fdt: Add tegra-usb bindings file from linux
fdt: Add staging area for device tree binding documentation
tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
tegra: fdt: Add Tegra2x device tree file from kernel
arm: fdt: Add skeleton device tree file from kernel
fdt: Add basic support for decoding GPIO definitions
fdt: Add functions to access phandles, arrays and bools
fdt: Tidy up a few fdtdec problems
fdt: Add tests for fdtdec
fdt: Add fdtdec_find_aliases() to deal with alias nodes
arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
net: fec_mxc: allow use with cache enabled
net: force PKTALIGN to ARCH_DMA_MINALIGN
i.MX28: Enable caches by default
i.MX28: Make use of the bounce buffer
i.MX28: Do data transfers via DMA in MMC driver
MMC: Implement generic bounce buffer
i.MX28: Add cache support to MXS NAND driver
i.MX28: Add cache support into the APBH DMA driver
ARM926EJS: Implement cache operations
board/vpac270/onenand.c: Fix build errors
nhk8815: fix build errors
atmel-boards: add missing atmel_mci.h
ARM: highbank: setup env from boot source register
ARM: highbank: change env config to use nvram
ARM: highbank: add reset support
ARM: highbank: Add boot counter support
ARM: highbank: change TEXT_BASE to 0x8000
ARM: highbank: fix us_to_tick calculation
ARM: highbank: add missing get_tbclk
ARM: highbank: fix warning for calxedaxgmac_initialize
net: calxedaxgmac: fix build due to missing __aligned definition
EXYNOS: Add structure for Exynos4 DMC
EXYNOS: SMDK5250: Support all 4 UARTs
ARM: fix s3c2410 timer code
ARM: davinci: fixes for cam_enc_4xx board
omap3_spi: receive transmit mode
calimain, enbw_cmc: Fix typo in comments
Davinci: ea20: use gpio framework to access gpios
OMAP3: mt_ventoux: sets its own mtdparts
OMAP3: mt_ventoux: updated timing for FPGA
twl4030: fix potential power supply handling issues
NAND: TI: fix warnings in omap_gpmc.c
cam_enc_4xx: Rename 'images' to 'imgs'
arm: Add Prep subcommand support to bootm
OMAP3: twister: add support to boot Linux from SPL
SPL: call cleanup_before_linux() before booting Linux
OMAP3: SPL: do not call I2C init if no I2C is set.
Add cache functions to SPL for armv7
devkit8000: Implement and activate direct OS boot
omap/spl: change output of spl_parse_image_header
omap-common/spl: Add linux boot to SPL
devkit8000/spl: init GPMC for dm9000 in SPL
omap-common: Add NAND SPL linux booting
devkit8000: add config for spl command
Add cmd_spl command
mx53ard: Initialize return code with error
mx53: Make PLL2 to be the parent of UART clock
configs: imx: Use CONFIG_SF_DEFAULT_CS
mx28evk: Provide default values for SPI bus and chip select
USB: ehci-mx6: Add proper IO accessors
mx6: Read silicon revision from register
i.MX28: Drop __naked function from spl_mem_init
mxs_spi: Return proper timeout error
i.MX28: Make the stabilization delays shorter
pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
mx6: Remove duplicate definition of ANATOP_BASE_ADDR
mx6: Fix reset cause for Power On Reset case
i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
i.MX28: Enable additional DRAM address bits
mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
mx31: add "ARM11P power gating" to get_reset_cause
mx31pdk: Fix CONFIG_SYS_MEMTEST_END
efikamx: Fix CONFIG_SYS_MEMTEST_END
mx53smd: Fix CONFIG_SYS_MEMTEST_END
mx53evk: Fix CONFIG_SYS_MEMTEST_END
mx51evk: Fix CONFIG_SYS_MEMTEST_END
i.MX6: mx6qsabrelite: add ext2 support
imximage: Remove overwriting of flash_offset
IXP: Fix GPIO_INT_ACT_LOW_SET()
IXP: Fix NAND build warning on PDNB3 and SCPU
IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
IXP: Squash warnings in IXP NPE
IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
IXP: Make IXP buildable with arm-linux- toolchains
Examples: Properly append LDFLAGS to LD command
SPL: Enable YMODEM support on BeagleBone and AM335x EVM
SPL: Add YMODEM over UART load support
SPL: Add README.omap3
README: document more SPL config options
spl.c: Use __noreturn decorator
config.mk: Check for -fstack-usage support
config.mk: Make cc-option create a file under include/generated
...

show more ...

Add cache functions to SPL for armv7

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>

scaled down version of generic libraries for SPL

Signed-off-by: Aneesh V <aneesh@ti.com>

armv7: add PL310 support to u-boot

PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430

Add support for some of the key PL310 operations
- Invalidate all

armv7: add PL310 support to u-boot

PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430

Add support for some of the key PL310 operations
- Invalidate all
- Invalidate range
- Flush(clean & invalidate) all
- Flush range

Signed-off-by: Aneesh V <aneesh@ti.com>

show more ...

armv7: rename cache related CONFIG flags

Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:

CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICA

armv7: rename cache related CONFIG flags

Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:

CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF

Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

arm: Use optimized memcpy and memset from linux

Using optimized versions of memset and memcpy from linux brings a quite
noticeable speed (x2 or better) improvement for these two functions.

Here are

arm: Use optimized memcpy and memset from linux

Using optimized versions of memset and memcpy from linux brings a quite
noticeable speed (x2 or better) improvement for these two functions.

Here are some numbers for test done with jadecpu

| HEAD(1)| HEAD(1)| HEAD(2)| HEAD(2)|
| | +patch | | +patch |
---------------------------+--------+--------+--------+--------+
Reset to prompt | 438ms | 330ms | 228ms | 120ms |
| | | | |
TFTP a 3MB img | 4782ms | 3428ms | 3245ms | 2820ms |
| | | | |
FATLOAD USB a 3MB img* | 8515ms | 8510ms | ------ | ------ |
| | | | |
BOOTM LZO img in RAM | 3473ms | 3168ms | 592ms | 592ms |
where CRC is | 615ms | 615ms | 54ms | 54ms |
uncompress | 2460ms | 2462ms | 450ms | 451ms |
final boot_elf | 376ms | 68ms | 65ms | 65ms |
| | | | |
BOOTM LZO img in FLASH | 3207ms | 2902ms | 1050ms | 1050ms |
where CRC is | 600ms | 600ms | 135ms | 135ms |
uncompress | 2209ms | 2211ms | 828ms | 828ms |
| | | | |
Copy 1.4MB from NOR to RAM | 134ms | 72ms | 120ms | 70ms |

(1) No dcache
(2) dcache enabled in board_init
*Does not work when dcache is on

Size impact:

C version:
text data bss dec hex filename
202862 18912 266456 488230 77326 u-boot

ASM version:
text data bss dec hex filename
203798 18912 266288 488998 77626 u-boot
222712 u-boot.bin

Signed-off-by: Matthias Weisser <weisserm@arcor.de>

show more ...

Switch from archive libraries to partial linking

Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. A

Switch from archive libraries to partial linking

Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
cpu/arm1176/cpu.c
cpu/arm1176/start.S
cpu/arm_cortexa8/s5pc1xx/Makefile
cpu/arm_cortexa8/s5pc1xx/clock.c
drivers/serial/serial_s

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
cpu/arm1176/cpu.c
cpu/arm1176/start.S
cpu/arm_cortexa8/s5pc1xx/Makefile
cpu/arm_cortexa8/s5pc1xx/clock.c
drivers/serial/serial_s5p.c
include/asm-arm/arch-s5pc1xx/clk.h
include/asm-arm/arch-s5pc1xx/gpio.h
include/asm-arm/arch-s5pc1xx/uart.h

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

show more ...

Move lib_$ARCH directories to arch/$ARCH/lib

Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux

Move lib_$ARCH directories to arch/$ARCH/lib

Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

show more ...