OMAP3: video: add macros to set display parameters

Add a common macros to set the registers for horizontal
and vertical timing.

Signed-off-by: Stefano Babic <sbabic@denx.de>

video: drop duplicate set of DISPC_CONFIG register

Signed-off-by: Stefano Babic <sbabic@denx.de>

OMAP3: add definition of CTRL_WKUP_CTRL register

AM/DM37x SoCs add the CTRL_WKUP_CTRL register. It contains the
GPIO_IO_PWRDNZ bit, which is required to be set to enable the I/O pads
of gpio_126, g

OMAP3: add definition of CTRL_WKUP_CTRL register

AM/DM37x SoCs add the CTRL_WKUP_CTRL register. It contains the
GPIO_IO_PWRDNZ bit, which is required to be set to enable the I/O pads
of gpio_126, gpio_127 and gpio_129.

Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Tom Rini <trini@ti.com>

show more ...

kw_spi: fix clock prescaler computation

The computation was not correct with low clock values: setting a 1MHz
clock would result in an overlap that would then configure a 25Mhz
clock.

This patch im

kw_spi: fix clock prescaler computation

The computation was not correct with low clock values: setting a 1MHz
clock would result in an overlap that would then configure a 25Mhz
clock.

This patch implements a correct computation method according to the
kirkwood functionnal spec. table 600 (Serial Memory Interface
Configuration Register).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-usb

* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus pro

Merge branch 'master' of git://git.denx.de/u-boot-usb

* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

pxa25x: Add UDC registers definitions

Signed-off-by: Łukasz Dałek <luk0104@gmail.com>

mxc: Define architecture identifier

Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.

The i.MX28 is omitted because its architecture is a b

mxc: Define architecture identifier

Define ARCH_MXC for i.MX devices. This is useful to identify features or
behaviors common to all i.MX SoCs.

The i.MX28 is omitted because its architecture is a bit different (like imx/mxc
vs. mxs in Linux).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>

show more ...

mxs: Convert timeout parameter to 'unsigned int'

For representing a timeout value, it makes more sense to pass it as
'unsigned int'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked

mxs: Convert timeout parameter to 'unsigned int'

For representing a timeout value, it makes more sense to pass it as
'unsigned int'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

MX28: DMA: Align the struct mxs_dma_desc

Align this structure to DMA alignment size.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@os

MX28: DMA: Align the struct mxs_dma_desc

Align this structure to DMA alignment size.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

gpio: add gpio api support to mx27 (v4)

The gpio api has been tested on an armadeus apf27.

Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Acked-by: Stefano Babic <sbabic@denx.de>

mx5: add iomux-mx51.h include

Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus t

mx5: add iomux-mx51.h include

Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus the required changes to make it work in U-Boot.

The contained pad settings are the minimum required to make an Efika MX boot
and get all the currently-implemented peripherals working in U-Boot.

It is recommended that this file not be just a dumping ground for pins but
only contain the settings required for all the boards using it.

Changes for v2:
* reference commit id from Linux kernel
* additionally roll in the USB pads
* removed GPIO_NUMBER define

Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

mxs: Rename 'mx28_dram_init' to 'mxs_dram_init'

The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.

The following boards has been

mxs: Rename 'mx28_dram_init' to 'mxs_dram_init'

The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.

The following boards has been changed:

* apx4devkit
* m28evk
* mx28evk
* sc_sps_1

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>

show more ...

mxs: Replace i.MX233 by i.MX23 on copyright header

All other header are going to use i.MX23 so we change this for
consistency.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>

mx35: Remove declaration of non-existing function

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx35: Move clock enums to clock.h

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx35: Remove declaration of non-existing function

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx35: Fix broken pin definitions

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx5: Undeclare imx_decode_pll()

The imx_decode_pll() function does not exist for mx5, so remove its declaration.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic

mx5: Undeclare imx_decode_pll()

The imx_decode_pll() function does not exist for mx5, so remove its declaration.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

MX: Set a common gpio.h for all i.MX

Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be

MX: Set a common gpio.h for all i.MX

Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>

show more ...

mxs: Use correct function name to initialize dram

commit d92591a (mxs: Convert sys_proto.h prefixes to 'mxs') introduced
a mxs_dram_init() function, which is not used anywhere.

Fix it, so that the

mxs: Use correct function name to initialize dram

commit d92591a (mxs: Convert sys_proto.h prefixes to 'mxs') introduced
a mxs_dram_init() function, which is not used anywhere.

Fix it, so that the following warning goes away:

mx28evk.c: In function ‘dram_init’:
mx28evk.c:67:2: warning: implicit declaration of function ‘mx28_dram_init’ [-Wimplicit-function-declaration]

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>

show more ...

imx-common/cmd_bmode.c: add imx bmode (bootmode) command

This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.

Currently, supp

imx-common/cmd_bmode.c: add imx bmode (bootmode) command

This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.

Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

iomux: move IOMUX_GPR13_xxx defines

Move mx6 specific defines to arch-mx6 directory.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

mx35: Remove duplicate GPIO3_BASE_ADDR

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx3: Fix typo on IPU_CONF_CSI_EN

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

mx35: Fix typo on EDIO

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>