| bafcf2db | 19-Jun-2017 |
Wadim Egorov <w.egorov@phytec.de> |
rockchip: Add basic support for phyCORE-RK3288 SoM based carrier board
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards
rockchip: Add basic support for phyCORE-RK3288 SoM based carrier board
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| f6f47c2e | 28-Jun-2017 |
Meng Dongyang <daniel.meng@rock-chips.com> |
rockchip: dts: rk3399: control vbus of typec by fixed regulator
Add fixed regulator for the port of typec0 and typec1 to control vbus
instead of gpio.
Signed-off-by: Meng Dongyang <daniel.meng@rock
rockchip: dts: rk3399: control vbus of typec by fixed regulator
Add fixed regulator for the port of typec0 and typec1 to control vbus
instead of gpio.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| 863456ad | 28-Jun-2017 |
Meng Dongyang <daniel.meng@rock-chips.com> |
rockchip: dts: rk3328: support and enable dwc2
Enable dwc2 controller and add fixed regulator for dwc2 controller to
control vbus.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed
rockchip: dts: rk3328: support and enable dwc2
Enable dwc2 controller and add fixed regulator for dwc2 controller to
control vbus.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| 296bd19e | 28-Jun-2017 |
Meng Dongyang <daniel.meng@rock-chips.com> |
rockchip: dts: rk3328: add fixed regulator node for xhci
The driver changes gpio to fixed regulator to control vbus, so add
fixed regulator node in DTS for xhci driver.
Signed-off-by: Meng Dongyang
rockchip: dts: rk3328: add fixed regulator node for xhci
The driver changes gpio to fixed regulator to control vbus, so add
fixed regulator node in DTS for xhci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| 522cd580 | 14-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: firefly-rk3399: dts: enable sdmmc device
Enable sdmmc device and add the spl boot device sequence.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chro
rockchip: firefly-rk3399: dts: enable sdmmc device
Enable sdmmc device and add the spl boot device sequence.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| ebac2cf0 | 14-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: rk3328: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Gl
rockchip: rk3328: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| 16e358ac | 14-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: rk3288: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Gl
rockchip: rk3288: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| 3f7a7255 | 14-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: rk3036: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Gl
rockchip: rk3036: dtsi use max-frequency for mmc node
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| b647442c | 23-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: rk322x: add dts file
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@the
rockchip: rk322x: add dts file
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
show more ...
|
| c541a7a1 | 23-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: dts: rk3368: add dmc node
Add dmc node to enable sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
| 8f313328 | 23-Jun-2017 |
Kever Yang <kever.yang@rock-chips.com> |
rockchip: dts: rk3328: add dmc node
Add a dmc node for sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> |
| 7bdc6947 | 27-Jun-2017 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: dts: OMAP5+: Enable gpio in SPL
gpio2 is used to detect lcd based on which pin mux is done in SPL.
gpio7 is used to enable vtt regulator. Enable these two gpio nodes
in SPL.
Signed-off-by: Lok
ARM: dts: OMAP5+: Enable gpio in SPL
gpio2 is used to detect lcd based on which pin mux is done in SPL.
gpio7 is used to enable vtt regulator. Enable these two gpio nodes
in SPL.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| d754254f | 26-Jun-2017 |
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> |
ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-bo
ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
show more ...
|
| ccaa83f8 | 26-Jun-2017 |
Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> |
ARM64: dts: hi3798cv200-poplar: add device tree bindings
Pulled from Linux 4.12-rc3
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org> |
| 6aba890e | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: k2g: Add DT support for K2G Industrial Communication Engine evm
Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-o
ARM: dts: k2g: Add DT support for K2G Industrial Communication Engine evm
Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| 42468c8b | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: k2g: Disable netcp by default
Disable netcp by default like all other peripherals in the dtsi file.
Enable the peripheral explicitly in the board specific dts file.
Signed-off-by: Frankli
ARM: dts: k2g: Disable netcp by default
Disable netcp by default like all other peripherals in the dtsi file.
Enable the peripheral explicitly in the board specific dts file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| 0d3f97db | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: keystone-k2g-evm: Add unit address to memory node
Upstream Linux has the unit address being added to the various 66AK2Gx
boards dts. Therefore, update the dts to mimic this change.
Also r
ARM: dts: keystone-k2g-evm: Add unit address to memory node
Upstream Linux has the unit address being added to the various 66AK2Gx
boards dts. Therefore, update the dts to mimic this change.
Also remove memory node from the base K2G dtsi file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| df5ec72d | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: keystone-k2g: Remove skeleton.dtsi
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#ad
ARM: dts: keystone-k2g: Remove skeleton.dtsi
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| 80364a42 | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
arm: dts: Add new "generic" 66AK2Gx device tree file.
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
arm: dts: Add new "generic" 66AK2Gx device tree file.
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| e0f3a3dc | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: k2g: Introduce U-boot specific dtsi file
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier t
ARM: dts: k2g: Introduce U-boot specific dtsi file
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier to
keep device tree files synced between U-boot and Linux.
For now only add nodes to allow i2c drivers to be probed early during
the boot process.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| a75df9ae | 16-Jun-2017 |
Cooper Jr., Franklin <fcooper@ti.com> |
ARM: dts: keystone-k2e-evm: Add U-boot specific dtsi file
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is neede
ARM: dts: keystone-k2e-evm: Add U-boot specific dtsi file
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1df ("ARM: keystone: Enable DM_I2C by default")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
show more ...
|
| be2787bf | 28-Jun-2017 |
Heiko Schocher <hs@denx.de> |
atmel, at91: fix taurus board
since commit: f8b7fff1d5c5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Weny
atmel, at91: fix taurus board
since commit: f8b7fff1d5c5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
show more ...
|
| be884598 | 23-Jun-2017 |
Heiko Schocher <hs@denx.de> |
atmel, at91: fix smartweb board
since commit: f8b7fff1d5c5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by:
atmel, at91: fix smartweb board
since commit: f8b7fff1d5c5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
show more ...
|
| 524b42bc | 24-Jun-2017 |
Tom Rini <trini@konsulko.com> |
Merge git://git.denx.de/u-boot-uniphier
- fix sparse warnings
- sync DT with Linux
- add new board support (LD11/LD20 global) |
| 7bf37804 | 22-Jun-2017 |
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> |
arm64: dts: uniphier: add support for LD20 Global board
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahi
arm64: dts: uniphier: add support for LD20 Global board
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
show more ...
|