rockchip: rk3288: add fastboot support

Enable fastboot feature on rk3288.

This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion witho

rockchip: rk3288: add fastboot support

Enable fastboot feature on rk3288.

This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

rockchip: add basic support for evb-rk3288 board

evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board

rockchip: add basic support for evb-rk3288 board

evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).

evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

sunxi: Enable NAND controller on the CHIP

Enable the NAND controller in the sun5i-r8-chip.dts.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@

sunxi: Enable NAND controller on the CHIP

Enable the NAND controller in the sun5i-r8-chip.dts.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

show more ...

sun5i: Add NAND controller to the sun5i DTSI

Add the NAND controller definition to sun5i.dtsi.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.

sun5i: Add NAND controller to the sun5i DTSI

Add the NAND controller definition to sun5i.dtsi.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

show more ...

ARM: dts: uniphier: renumber serial aliases for Gentil/Vodka boards

On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used inst

ARM: dts: uniphier: renumber serial aliases for Gentil/Vodka boards

On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.

[ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

show more ...

ARM: tegra: split p2771-0000 build

There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separa

ARM: tegra: split p2771-0000 build

There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.

With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

ARM: tegra: fix Tegra186 DT GPIO binding header

Tegra186 uses different GPIO port IDs compared to previous chips. Make
sure the SoC DT file includes the correct GPIO binding header.

Signed-off-by:

ARM: tegra: fix Tegra186 DT GPIO binding header

Tegra186 uses different GPIO port IDs compared to previous chips. Make
sure the SoC DT file includes the correct GPIO binding header.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: Add defconfig and dts file for the Orange Pi Lite SBC

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio

sunxi: Add defconfig and dts file for the Orange Pi Lite SBC

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Sync sun8i-h3-orangepi-plus.dts with upstream

This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.

Signed-off-by: Hans de Goede <hdeg

sunxi: Sync sun8i-h3-orangepi-plus.dts with upstream

This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-samsung

net: Add EMAC driver for H3/A83T/A64 SoCs.

This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).

BIG Thanks to Andre for provi

net: Add EMAC driver for H3/A83T/A64 SoCs.

This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).

BIG Thanks to Andre for providing some of the DT code.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

rockchip: Update the sdram-channel property to support of-platdata

Add an extra byte so that this data is not byteswapped. Add a comment to
the code to explain the purpose.

Signed-off-by: Simon Gla

rockchip: Update the sdram-channel property to support of-platdata

Add an extra byte so that this data is not byteswapped. Add a comment to
the code to explain the purpose.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

ARM: exynos4: dts: add the prefix '/' for aliases nodes

It's correct to use '/' as prefix for aliases nodes.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.ka

ARM: exynos4: dts: add the prefix '/' for aliases nodes

It's correct to use '/' as prefix for aliases nodes.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz

According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3

ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz

According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: K2G: Add support for QSPI controller

K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash conn

ARM: dts: K2G: Add support for QSPI controller

K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor
flash slave node for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: k2g: add support for Davinci SPI controller

K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes f

ARM: dts: k2g: add support for Davinci SPI controller

K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: k2l: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as

ARM: dts: k2l: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: k2e: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as

ARM: dts: k2e: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: k2hk: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as

ARM: dts: k2hk: Enable Davinci SPI controller

Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

ARM: dts: keystone2: add SPI aliases for davinci SPI nodes

Add aliases for SPI nodes in order for it to be probed by the DM
framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Ri

ARM: dts: keystone2: add SPI aliases for davinci SPI nodes

Add aliases for SPI nodes in order for it to be probed by the DM
framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>

show more ...

video: tegra: Move to using simple-panel and pwm-backlight

We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those inst

video: tegra: Move to using simple-panel and pwm-backlight

We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.

This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:

- colibri
- medcom-wide
- paz00
- tec

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

tegra: dts: Sync tegra20 device tree files with Linux

Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in

tegra: dts: Sync tegra20 device tree files with Linux

Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

show more ...

sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, U

sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

The DTS file is identical to the one submitted to the upstream kernel.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...