Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2017.03

- ATF handoff
- DT syncups
- gem: Use wait_for_bit(), add simple clk support
- Simple clk driv

Merge tag 'xilinx-for-v2017.03' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2017.03

- ATF handoff
- DT syncups
- gem: Use wait_for_bit(), add simple clk support
- Simple clk driver for ZynqMP
- Other small changes

show more ...

ARM64: zynqmp: Generate handoff structure for ATF

Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structu

ARM64: zynqmp: Generate handoff structure for ATF

Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.

Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze

ARM64: zynqmp: Add SPL support support

Support RAM and MMC boot mode in SPL also with SPL_FIT images.

In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2

ARM64: zynqmp: Add SPL support support

Support RAM and MMC boot mode in SPL also with SPL_FIT images.

In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>

2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>

3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/

and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0

psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.

The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze

zynqmp: Add support for IP detection via SLCR

SLCR can be used for IP configuration setting.
Add SLCR skeleton to enable run time checking.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze

zynqmp: Add support for R5 sw loading

Add support for loading sw for R5 with enabling for zynqmp.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <si

zynqmp: Add support for R5 sw loading

Add support for loading sw for R5 with enabling for zynqmp.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'xnext/zynqmp' of git://www.denx.de/git/u-boot-microblaze

arm64: Add Xilinx ZynqMP support

Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.

Signed-off-by: Michal Simek <michal.simek@xilinx.c

arm64: Add Xilinx ZynqMP support

Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...