Merge branch 'master' of git://git.denx.de/u-boot-nand-flash

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

On-chip ROM boot: MPC8536DS support

The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the

On-chip ROM boot: MPC8536DS support

The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.

The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.

The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.

This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

NAND boot: MPC8536DS support

MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is

NAND boot: MPC8536DS support

MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.

When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.

This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.

Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

Refactor OneNAND IPL code

Refactoring the OneNAND IPL code

and some minor fixed:
- Remove unnecessary header file
- Fix wrong access at read interrupt
- The recent OneNAND has 4KiB pagesize

Also B

Refactor OneNAND IPL code

Refactoring the OneNAND IPL code

and some minor fixed:
- Remove unnecessary header file
- Fix wrong access at read interrupt
- The recent OneNAND has 4KiB pagesize

Also Board can override OneNAND IPL image

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

show more ...

sbc8349: tidy up Makefile to use new configuration script.

Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the board config heade

sbc8349: tidy up Makefile to use new configuration script.

Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the board config header. This takes advantage of
that for the sbc8349 board.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Merge branch 'master' of /home/wd/git/u-boot/custodians

sbc85x0: tidy up Makefile to use new configuration script.

Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the boards config head

sbc85x0: tidy up Makefile to use new configuration script.

Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the boards config header. This takes advantage of
that for the sbc8540/sbc8560 boards.

There were a couple of cheezy comments pointing at incorrect
files, or files that don't exist, so I've cleaned those up too.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

sbc8548: allow enabling PCI via a make config option

Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CO

sbc8548: allow enabling PCI via a make config option

Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CONFIG_SYS_NS16550_CLK too, which was
not real user friendly,

This adds the typical PCI and clock speed make targets to the
toplevel Makefile in accordance with what is being done with
other boards (i.e. using the "-t" to mkconfig).

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

ppc/85xx: Simplify the top makefile for P1_P2_RDB boards

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

ppc/85xx: Simplify the top makefile for 36-bit config for P2020DS

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

ppc/85xx: Simplify the top makefile for 36-bit config for MPC8572DS

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

ppc/85xx: simplify the top makefile for 36-bit config for mpc8536ds

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Merge branch 'master' of git://git.denx.de/u-boot-microblaze

Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

microblaze: Remove AtmarkTechno Suzaku board

Users should use microblaze-generic platform.
This platform is longer not supported.

Signed-off-by: Michal Simek <monstr@monstr.eu>

ppc4xx: Rename compactcenter to intip

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>

mkimage: Add Kirkwood Boot Image support (kwbimage)

This patch adds support for "kwbimage" (Kirkwood Boot Image)
image types to the mkimage code.

For details refer to docs/README.kwbimage

This pat

mkimage: Add Kirkwood Boot Image support (kwbimage)

This patch adds support for "kwbimage" (Kirkwood Boot Image)
image types to the mkimage code.

For details refer to docs/README.kwbimage

This patch is tested with Sheevaplug board

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ron Lee <ron@debian.org>

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

show more ...

Remove "atmel_df_pow2" binary with "make clean"

Commit 65f6f07b added support for the atmel_df_pow2 standalone program
but missed to add a rule to remove it to the "clean" make target.

Signed-off-b

Remove "atmel_df_pow2" binary with "make clean"

Commit 65f6f07b added support for the atmel_df_pow2 standalone program
but missed to add a rule to remove it to the "clean" make target.

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

ARM: DaVinci: Adding Support for DaVinci DM365 EVM

This patch adds support for the DM365 EVM.
It has been tested on a DM365 EVM.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Add support for the DevKit8000 board

This patch adds support for the DevKit8000 board.

Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>

omap3: move the other boards to board/

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

arm: move Logicpd's boards to board/logicpd/

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

omap: move TI's boards to board/ti/

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>