plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes s

plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.

Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>

show more ...

plat/marvell/armada/common/mss: use MSS SRAM in secure mode

The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image fro

plat/marvell/armada/common/mss: use MSS SRAM in secure mode

The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image from DRAM to IRAM.
This patch adds support for using the MSS SRAM as intermediate
storage. The MSS FW image is loaded by application CPU into the
MSS SRAM first, then transferred to MSS IRAM by MSS DMA.
Such change allows the CP MSS image load in secure mode.

Change-Id: Iee7a51d157743a0bdf8acb668ee3d599f760a712
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaszczyk@marvell.com>

show more ...

plat: marvell: t9130: pass actual CP count for load_image

Add CN913x case to bl2_plat_get_cp_count.
Fix loading of cp1/2 image. This is a preparation
patch for adding CN913x SoC family support.

Cha

plat: marvell: t9130: pass actual CP count for load_image

Add CN913x case to bl2_plat_get_cp_count.
Fix loading of cp1/2 image. This is a preparation
patch for adding CN913x SoC family support.

Change-Id: Id84a30203d20572fc0dfd3f91ea395c199a85fe9
Signed-off-by: Ben Peled <bpeled@marvell.com>

show more ...

plat: marvell: armada: a8k: check CCU window state before loading MSS BL2

Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL

plat: marvell: armada: a8k: check CCU window state before loading MSS BL2

Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL2 stage the CCU Win-2 points to DRAM. If additional mapping is
added to MSS BL2 stage initialization, the DDR entry will be destroyed
and lead to the system hang.

Change-Id: I215e83508acc37d54dab6954d791b9a74cc883ca
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done af

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.

Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea
Signed-off-by: Ben Peled <bpeled@marvell.com>

show more ...

plat: marvell: armada: configure amb for all CPs

Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.

Change-Id:

plat: marvell: armada: configure amb for all CPs

Before this patch the configuration took place only for CP0 and CP1, but
since new platforms can contains up to 3 CPs update is required.

Change-Id: Iebd50bbe7b9772063e2c4efb3a7ecbfd593e950d
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
pla

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

show more ...