FVP: Add dummy configs for BL31, BL32 and BL33

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined

FVP: Add dummy configs for BL31, BL32 and BL33

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

ARM Platforms: Support RAS

- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.

- Call the common RAS initialisation from ARM BL31 setup.

- Add empty d

ARM Platforms: Support RAS

- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.

- Call the common RAS initialisation from ARM BL31 setup.

- Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

ARM Platforms: Load HW_CONFIG in BL2

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
propert

ARM Platforms: Load HW_CONFIG in BL2

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

ARM Platforms: Migrate to new BL handover interface

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to

ARM Platforms: Migrate to new BL handover interface

This patch migrates the ARM Standard platforms to the new BL
handover interface. The arm_blx_early_platform_setup() functions
are also modified to take in 4 arguments. The `ARM_BL31_PLAT_PARAM_VAL`
value passed to BL31 from BL2 is now in arg3 in preparation of dynamic
configuration arguments.

Change-Id: I33e8e61325a19e7a7127b1ff203c3b86921bf153
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

ARM platforms: Fix console address for flush

The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This

ARM platforms: Fix console address for flush

The console core flush API expects the base address in the first
register, but ARM helpers currently sets the second register with the
base address. This causes an assert failure.

This patch fixes that.

Change-Id: Ic54c423cd60f2756902ab3cfc77b3de2ac45481e
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

ARM platforms: Allow platforms to define SDEI events

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of privat

ARM platforms: Allow platforms to define SDEI events

With this patch, ARM platforms are expected to define the macros
PLAT_ARM_SDEI_PRIVATE_EVENTS and PLAT_ARM_SDEI_SHARED_EVENTS as a list
of private and shared events, respectively. This allows for individual
platforms to define their own events.

Change-Id: I66851fdcbff83fd9568c2777ade9eb12df284b49
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

Refactor Statistical Profiling Extensions implementation

Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Ad

Refactor Statistical Profiling Extensions implementation

Factor out SPE operations in a separate file. Use the publish
subscribe framework to drain the SPE buffers before entering secure
world. Additionally, enable SPE before entering normal world.

A side effect of this change is that the profiling buffers are now
only drained when a transition from normal world to secure world
happens. Previously they were drained also on return from secure
world, which is unnecessary as SPE is not supported in S-EL1.

Change-Id: I17582c689b4b525770dbb6db098b3a0b5777b70a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

show more ...

ARM platforms: Enable SDEI

Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful

ARM platforms: Enable SDEI

Support SDEI on ARM platforms using frameworks implemented in earlier
patches by defining and exporting SDEI events: this patch defines the
standard event 0, and a handful of shared and private dynamic events.

Change-Id: I9d3d92a92cff646b8cc55eabda78e140deaa24e1
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

ARM platforms: Define exception macros

Define number of priority bits, and allocate priority levels for SDEI.

Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan

ARM platforms: Define exception macros

Define number of priority bits, and allocate priority levels for SDEI.

Change-Id: Ib6bb6c5c09397f7caef950c4caed5a737b3d4112
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

Add Trusted OS extra image parsing support for ARM standard platforms

Trusted OS may have extra images to be loaded. Load them one by one
and do the parsing. In this patch, ARM TF need to load up to

Add Trusted OS extra image parsing support for ARM standard platforms

Trusted OS may have extra images to be loaded. Load them one by one
and do the parsing. In this patch, ARM TF need to load up to 3 images
for optee os: header, pager and paged images. Header image is the info
about optee os and images. Pager image include pager code and data.
Paged image include the paging parts using virtual memory.

Change-Id: Ia3bcfa6d8a3ed7850deb5729654daca7b00be394
Signed-off-by: Summer Qin <summer.qin@arm.com>

show more ...

ARM plat changes to enable CryptoCell integration

This patch makes the necessary changes to enable ARM platform to
successfully integrate CryptoCell during Trusted Board Boot. The
changes are as fol

ARM plat changes to enable CryptoCell integration

This patch makes the necessary changes to enable ARM platform to
successfully integrate CryptoCell during Trusted Board Boot. The
changes are as follows:

* A new build option `ARM_CRYPTOCELL_INTEG` is introduced to select
the CryptoCell crypto driver for Trusted Board boot.

* The TrustZone filter settings for Non Secure DRAM is modified
to allow CryptoCell to read this memory. This is required to
authenticate BL33 which is loaded into the Non Secure DDR.

* The CSS platforms are modified to use coherent stacks in BL1 and BL2
when CryptoCell crypto is selected. This is because CryptoCell makes
use of DMA to transfer data and the CryptoCell SBROM library allocates
buffers on the stack during signature/hash verification.

Change-Id: I1e6f6dcd1899784f1edeabfa2a9f279bbfb90e31
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

aarch64: Enable Statistical Profiling Extensions for lower ELs

SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, befo

aarch64: Enable Statistical Profiling Extensions for lower ELs

SPE is only supported in non-secure state. Accesses to SPE specific
registers from SEL1 will trap to EL3. During a world switch, before
`TTBR` is modified the SPE profiling buffers are drained. This is to
avoid a potential invalid memory access in SEL1.

SPE is architecturally specified only for AArch64.

Change-Id: I04a96427d9f9d586c331913d815fdc726855f6b0
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

show more ...

Use SPDX license identifiers

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by

Use SPDX license identifiers

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

show more ...

Add and use plat_crash_console_flush() API

This API makes sure that all the characters sent to the crash console
are output before returning from it.

Porting guide updated.

Change-Id: I1785f970a40

Add and use plat_crash_console_flush() API

This API makes sure that all the characters sent to the crash console
are output before returning from it.

Porting guide updated.

Change-Id: I1785f970a40f6aacfbe592b6a911b1f249bb2735
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

ARM platform changes for new version of image loading

This patch adds changes in ARM platform code to use new
version of image loading.

Following are the major changes:
-Refactor the signatures f

ARM platform changes for new version of image loading

This patch adds changes in ARM platform code to use new
version of image loading.

Following are the major changes:
-Refactor the signatures for bl31_early_platform_setup()
and arm_bl31_early_platform_setup() function to use
`void *` instead of `bl31_params_t *`.
-Introduce `plat_arm_bl2_handle_scp_bl2()` to handle
loading of SCP_BL2 image from BL2.
-Remove usage of reserve_mem() function from
`arm_bl1_early_platform_setup()`
-Extract BL32 & BL33 entrypoint info, from the link list
passed by BL2, in `arm_bl31_early_platform_setup()`
-Provides weak definitions for following platform functions:
plat_get_bl_image_load_info
plat_get_next_bl_params
plat_flush_next_bl_params
bl2_plat_handle_post_image_load
-Instantiates a descriptor array for ARM platforms
describing image and entrypoint information for
`SCP_BL2`, `BL31`, `BL32` and `BL33` images.

All the above changes are conditionally compiled using the
`LOAD_IMAGE_V2` flag.

Change-Id: I5e88b9785a3df1a2b2bbbb37d85b8e353ca61049

show more ...

Move `arm_common.c` out of aarch64 folder

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64

Move `arm_common.c` out of aarch64 folder

This patch moves the `arm_common.c` file from `plat/arm/common/aarch64/`
to the parent directory since the functions implemented in the file are
not AArch64 specific. The platform makefiles are also modified for this
change.

Change-Id: I776d2e4958f59041476cf2f53a9adb5b2d304ee0

show more ...

Rework type usage in Trusted Firmware

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as

Rework type usage in Trusted Firmware

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:

* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
whether AArch64 or AArch32.
* Use generic C types where-ever possible.

In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.

Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8

show more ...

Add some verbose traces in arm_setup_page_tables()

This patch adds some verbose traces in the arm_setup_page_tables()
function to print the extents of the different memory regions it maps.

Change-I

Add some verbose traces in arm_setup_page_tables()

This patch adds some verbose traces in the arm_setup_page_tables()
function to print the extents of the different memory regions it maps.

Change-Id: Ia3ae1053e7ebf3579601ff9238b0e3791eb1e9e4

show more ...

ARM platforms: Add support for SEPARATE_CODE_AND_RODATA

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and re

ARM platforms: Add support for SEPARATE_CODE_AND_RODATA

The arm_setup_page_tables() function used to expect a single set of
addresses defining the extents of the whole read-only section, code
and read-only data mixed up, which was mapped as executable.

This patch changes this behaviour. arm_setup_page_tables() now
expects 2 separate sets of addresses:

- the extents of the code section;
- the extents of the read-only data section.

The code is mapped as executable, whereas the data is mapped as
execute-never. New #defines have been introduced to identify the
extents of the code and the read-only data section. Given that
all BL images except BL1 share the same memory layout and linker
script structure, these #defines are common across these images.
The slight memory layout differences in BL1 have been handled by
providing values specific to BL1.

Note that this patch also affects the Xilinx platform port, which
uses the arm_setup_page_tables() function. It has been updated
accordingly, such that the memory mappings on this platform are
unchanged. This is achieved by passing null values as the extents
of the read-only data section so that it is ignored. As a result,
the whole read-only section is still mapped as executable.

Fixes ARM-software/tf-issues#85

Change-Id: I1f95865c53ce6e253a01286ff56e0aa1161abac5

show more ...

Introduce arm_setup_page_tables() function

This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and do

Introduce arm_setup_page_tables() function

This patch introduces the arm_setup_page_tables() function to
set up page tables on ARM platforms. It replaces the
arm_configure_mmu_elx() functions and does the same thing except
that it doesn't enable the MMU at the end. The idea is to reduce
the amount of per-EL code that is generated by the C preprocessor
by splitting the memory regions definitions and page tables creation
(which is generic) from the MMU enablement (which is the only per-EL
configuration).

As a consequence, the call to the enable_mmu_elx() function has been
moved up into the plat_arch_setup() hook. Any other ARM standard
platforms that use the functions `arm_configure_mmu_elx()` must be
updated.

Change-Id: I6f12a20ce4e5187b3849a8574aac841a136de83d

show more ...

Fix a syntax error

Building TF with ERROR_DEPRECATED=1 fails because of a missing
semi-column. This patch fixes this syntax error.

Change-Id: I98515840ce74245b0a0215805f85c8e399094f68

Implement plat_get_syscnt_freq2 on platforms

Replaced plat_get_syscnt_freq by plat_get_syscnt_freq2 on all
upstream platforms.

Change-Id: I3248f3f65a16dc5e9720012a05c35b9e3ba6abbe

Conditionally compile `plat_get_syscnt_freq()` in ARM standard platforms

This patch puts the definition of `plat_get_syscnt_freq()`
under `#ifdef ARM_SYS_CNTCTL_BASE` in arm_common.c file.
This is t