/*
 * Copyright (c) 2018, Arm Limited and Contributors. All rights reserved.
 * Copyright (c) 2022-2023, Advanced Micro Devices, Inc. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#ifndef PLAT_MACROS_S
#define PLAT_MACROS_S

#include <drivers/arm/gic_common.h>
#include <drivers/arm/gicv2.h>
#include <drivers/arm/gicv3.h>

#include "../include/platform_def.h"

.section .rodata.gic_reg_name, "aS"
/* Applicable only to GICv2 and GICv3 with SRE disabled (legacy mode) */
gicc_regs:
	.asciz "gicc_hppir", "gicc_ahppir", "gicc_ctlr", ""

/* Applicable only to GICv3 with SRE enabled */
icc_regs:
	.asciz "icc_hppir0_el1", "icc_hppir1_el1", "icc_ctlr_el3", ""

/* Registers common to both GICv2 and GICv3 */
gicd_pend_reg:
	.asciz "gicd_ispendr regs (Offsets 0x200 - 0x278)\n Offset:\t\t\tvalue\n"
newline:
	.asciz "\n"
spacer:
	.asciz ":\t\t0x"

	/* ---------------------------------------------
	 * The below utility macro prints out relevant GIC
	 * registers whenever an unhandled exception is
	 * taken in BL31 on Versal platform.
	 * Expects: GICD base in x16, GICC base in x17
	 * Clobbers: x0 - x10, sp
	 * ---------------------------------------------
	 */
	.macro versal_print_gic_regs
	/* Check for GICv3 system register access */
	mrs	x7, id_aa64pfr0_el1
	ubfx	x7, x7, #ID_AA64PFR0_GIC_SHIFT, #ID_AA64PFR0_GIC_WIDTH
	cmp	x7, #1
	b.ne	print_gicv2

	/* Check for SRE enable */
	mrs	x8, ICC_SRE_EL3
	tst	x8, #ICC_SRE_SRE_BIT
	b.eq	print_gicv2

	/* Load the icc reg list to x6 */
	adr	x6, icc_regs
	/* Load the icc regs to gp regs used by str_in_crash_buf_print */
	mrs	x8, ICC_HPPIR0_EL1
	mrs	x9, ICC_HPPIR1_EL1
	mrs	x10, ICC_CTLR_EL3
	/* Store to the crash buf and print to console */
	bl	str_in_crash_buf_print
	b	print_gic_common

print_gicv2:
	/* Load the gicc reg list to x6 */
	adr	x6, gicc_regs
	/* Load the gicc regs to gp regs used by str_in_crash_buf_print */
	ldr	w8, [x17, #GICC_HPPIR]
	ldr	w9, [x17, #GICC_AHPPIR]
	ldr	w10, [x17, #GICC_CTLR]
	/* Store to the crash buf and print to console */
	bl	str_in_crash_buf_print

print_gic_common:
	/* Print the GICD_ISPENDR regs */
	add	x7, x16, #GICD_ISPENDR
	adr	x4, gicd_pend_reg
	bl	asm_print_str
gicd_ispendr_loop:
	sub	x4, x7, x16
	cmp	x4, #0x280
	b.eq	exit_print_gic_regs
	bl	asm_print_hex

	adr	x4, spacer
	bl	asm_print_str

	ldr	x4, [x7], #8
	bl	asm_print_hex

	adr	x4, newline
	bl	asm_print_str
	b	gicd_ispendr_loop
exit_print_gic_regs:
	.endm

	/* ---------------------------------------------
	 * The below required platform porting macro
	 * prints out relevant GIC and CCI registers
	 * whenever an unhandled exception is taken in
	 * BL31.
	 * Clobbers: x0 - x10, x16, x17, sp
	 * ---------------------------------------------
	 */
	.macro plat_crash_print_regs
	mov_imm	x17, PLAT_ARM_GICD_BASE
	mov_imm	x16, PLAT_ARM_GICR_BASE
	versal_print_gic_regs
	.endm

#endif /* PLAT_MACROS_S */
