/* SPDX-License-Identifier: BSD-2-Clause */
/*
 * Copyright 2021 NXP
 * I2C driver for I2C Controller
 */

#ifndef __DRIVERS_LS_I2C_H
#define __DRIVERS_LS_I2C_H

#include <io.h>
#include <stdint.h>
#include <tee_api_types.h>

/*
 * Module Disable
 * 0b - The module is enabled. You must clear this field before any other IBCR
 * fields have any effect.
 * 1b - The module is reset and disabled. This is the power-on reset situation.
 * When high, the interface is held in reset, but registers can still be
 * accessed. Status register fields (IBSR) are not valid when the module
 * is disabled.
 */
#define I2C_IBCR_MDIS U(0x80)

/* I2c Bus Interrupt Enable */
#define I2C_IBCR_IBIE U(0x40)

/*
 * Master / Slave Mode 0b - Slave mode 1b - Master mode
 * When you change this field from 0 to 1, the module generates a START signal
 * on the bus and selects the master mode. When you change this field from 1 to
 * 0, the module generates a STOP signal and changes the operation mode from
 * master to slave. You should generate a STOP signal only if IBSR[IBIF]=1.
 * The module clears this field without generating a STOP signal when the
 * master loses arbitration.
 */
#define I2C_IBCR_MSSL U(0x20)

/* 0b - Receive 1b - Transmit */
#define I2C_IBCR_TXRX U(0x10)

/*
 * Data acknowledge disable
 * Values written to this field are only used when the I2C module is a receiver,
 * not a transmitter.
 * 0b - The module sends an acknowledge signal to the bus at the 9th clock bit
 * after receiving one byte of data.
 * 1b - The module does not send an acknowledge-signal response (that is,
 * acknowledge bit = 1).
 */
#define I2C_IBCR_NOACK U(0x08)

/*
 * Repeat START
 * If the I2C module is the current bus master, and you program RSTA=1, the I2C
 * module generates a repeated START condition. This field always reads as a 0.
 * If you attempt a repeated START at the wrong time, if the bus is owned by
 * another master the result is loss of arbitration.
 */
#define I2C_IBCR_RSTA U(0x04)

/* DMA enable */
#define I2C_IBCR_DMAEN U(0x02)

/* Transfer Complete */
#define I2C_IBSR_TCF U(0x80)

/* I2C bus Busy. 0b - Bus is idle, 1b - Bus is busy */
#define I2C_IBSR_IBB U(0x20)

/* Arbitration Lost. software must clear this field by writing a one to it. */
#define I2C_IBSR_IBAL U(0x10)

/* I2C bus interrupt flag */
#define I2C_IBSR_IBIF U(0x02)

/*
 * Received acknowledge
 * 0b - Acknowledge received
 * 1b - No acknowledge received
 */
#define I2C_IBSR_RXAK U(0x01)

/* Bus idle interrupt enable */
#define I2C_IBIC_BIIE U(0x80)

/* Glitch filter enable */
#define I2C_IBDBG_GLFLT_EN U(0x08)

#define I2C_FLAG_WRITE U(0x00000000)
#define I2C_FLAG_READ  U(0x00000001)

#define I2C_BUS_TEST_BUSY      true
#define I2C_BUS_TEST_IDLE      !I2C_BUS_TEST_BUSY
#define I2C_BUS_TEST_RX_ACK    true
#define I2C_BUS_NO_TEST_RX_ACK !I2C_BUS_TEST_RX_ACK

#define I2C_NUM_RETRIES	   U(500)

struct i2c_regs {
	uint8_t ibad;  /* I2c Bus Address Register */
	uint8_t ibfd;  /* I2c Bus Frequency Divider Register */
	uint8_t ibcr;  /* I2c Bus Control Register */
	uint8_t ibsr;  /* I2c Bus Status Register */
	uint8_t ibdr;  /* I2C Bus Data I/O Register */
	uint8_t ibic;  /* I2C Bus Interrupt Config Register */
	uint8_t ibdbg; /* I2C Bus Debug Register */
};

/*
 * sorted list of clock divisor, ibfd register value pairs
 */
struct i2c_clock_divisor_pair {
	uint16_t divisor;
	uint8_t ibfd; /* I2c Bus Frequency Divider Register value */
};

/*
 * I2C device operation
 * The i2c_operation describes a subset of an I2C transaction in which
 * the I2C controller is either sending or receiving bytes from the bus.
 * Some transactions will consist of a single operation while others will
 * be two or more.
 */
struct i2c_operation {
	/* Flags to qualify the I2C operation. */
	uint32_t flags;

	/*
	 * Number of bytes to send to or receive from the I2C device.A ping
	 * is indicated by setting the length_in_bytes to zero.
	 */
	unsigned int length_in_bytes;

	/*
	 * Pointer to a buffer containing the data to send or to receive from
	 * the I2C device.  The Buffer must be at least length_in_bytes in size.
	 */
	uint8_t *buffer;
};

/*
 * Structure to initialize I2C controller.
 */
struct ls_i2c_data {
	/* I2C Controller to initialize */
	uint8_t i2c_controller;
	/*
	 * base will be filled by i2c_init() which will be used in
	 * subsequent calls for reading/writing data.
	 */
	vaddr_t base;
	/* I2C bus clock frequency */
	uint64_t i2c_bus_clock;
	/* I2C speed */
	uint64_t speed;
};

/*
 * Structure to fill for I2C read/write operation
 */
struct i2c_reg_request {
	/*
	 * Number of operations to perform.
	 * This will depend on peripheral for which it is used.
	 */
	unsigned int operation_count;
	/* Operation to perform */
	struct i2c_operation *operation;
};

/*
 * Initialize I2C Controller, based on data passed in
 * i2c_data.
 */
TEE_Result i2c_init(struct ls_i2c_data *i2c_data);

/*
 * Software reset of the entire I2C module.
 * The module is reset and disabled.
 * Status register fields (IBSR) are cleared.
 * base       Base Address of I2c controller's registers
 */
void i2c_reset(vaddr_t base);

/*
 * Transfer data to/from I2c slave device
 * base			Base Address of I2c controller's registers
 * slave_address	Slave Address from which data is to be read
 * i2c_operation	Pointer to an i2c_operation structure
 * operation_count	Number of operations.
 */
TEE_Result i2c_bus_xfer(vaddr_t base, uint32_t slave_address,
			struct i2c_operation *i2c_operation,
			unsigned int operation_count);

#endif /* __DRIVERS_LS_I2C_H */